Flying Leathernecks

Decal..

This set contains one (1) pod. The AN/ALQ-164 Defensive Electronic Countermeasures (DECM) Pod was used frequently by the US Marine Corps AV-8B Harriers during Operation Desert Storm.CAD by Craig Sargent..

This set includes six (6) Mk-83 1000lb bombs with conical fins and six (6) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensively throughout the war. Yours truly built ..

This set includes six (6) Mk-83 1000lb bombs with BSU-85 fins and six (6) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensively throughout the war. Yours truly built s..

This set contains six (6) Mk-82 500lb bombs with thermal protective coating and BSU-86 retarded fins. Also included are six (6) each of the following:M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail section..

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following:M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail section to remove remnants of support ..

This set includes six Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs.Accurately reproduced using personal measurements and photos of the real item. Parts come as seen in the photo, leaving minimal work for the modeler..

This set includes six (6) Mk-77 Fire Bombs.Light sanding to remove print support nibs is necessary on the aft end of the bomb..

This set includes twelve (12) Mk-76 25 lb Practice Bombs..

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

Set of four (4) 3D printed launchersIn February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.The standoff adapters in ..

Set of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. How..

Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

Set includes six (6) Mk-82/BLU-111 bombs with KMU-572 tail assemblies and nose strakes attached.Also included are six (6) DSU-33 proximity fuzes, six (6) MXU-735 solid nose plugs and six (6) Ogive nose plugs...

Set includes six (6) Mk-83/BLU-110 bombs with KMU-559 guidance kit and tail assemblies attached.Also included are six (6) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

3D Resin..

Set FL172-2001 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532 and aircraft upgraded to F/A-18A++ standard. The F/A-18A++ can be easily identified by..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/72 F/A-18A/B/C/D Hornet kits...

Set FL172-2000 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and B.They not only correct the shape of the kit pylons, they provide details unmatched by the kit supplied parts. All pylons are 3D printed and require little clean up to remove the..

Set of 16 correctly sized and shaped pitot tubes for use on the Legacy F/A-18, F-14, A-7, F-8, AV-8B and several other aircraft that use this style of pitot tube.3D printed and lightly supported for easy removal from block...