Flying Leathernecks

In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. However, all of these changes were either..

This set includes four (4) empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Rocket tubes are hollow the entire length of the pod to dep..

Designed by Petr Haupt, this set includes two (2) LAU-33 Pods, four (4) Mk-71 Rocket Motors, four (4) Mk32 Mod 0 anti tank / anti personnel warheads with Mk188 Impact Fuzes and four (4) Mk32 Mod 0 warheads with Mk93 proximity fuzes..

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) launchersUsed to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) missile launchers.Used to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchers.Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage..

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles...

LAU-115/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles. ..

This set includes eight (8) wing pylons, one (1) centerline pylons, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...

3D ResinThis is a simple tool that can be used over and over.If built as designed, the vertical tails in the Hasegawa 1/48 Hornets angle too far out. This jig helps set them at the correct angle.Simply score (do not cut off) the outside surface of the locating tabs on the tail parts where it me..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/48 F/A-18A/B/C/D Hornet kits...

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

This set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment points smoot..

3D ResinThis set includes three (3) pieces that make up the belly strap found on late F-4E and all F-4G Phantoms. Designed to be used on the Meng kits, it may work with other kits with some adjustments.The strap was also found on the F-4S and the F-4J's operated by the UK.Parts come as shown a..

Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/48 F-16 kits...

Vinyl Mask..

This set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene.Parts come as shown in photo. Very light sanding needed on one surface needed prior to painting...