Flying Leathernecks

Mk-76 practice bombs (12 per pack)These new 3D printed bombs come ready to paint and install. Some very light clean up may be necessary at the aft end of the fins to remove any trace of the printing supports.Simply paint FS35109 Blue and install!..

This set includes four (4) launchers designed to fit the Tamiya F-4 wing pylons in anticipation for later variants. This launcher was used from 1976 to 1987..

This set includes four (4) missile launchers designed to fit the Tamiya F-4B pylons and were used from 1969 to 1975...

This set includes four (4) missile launchers designed to fit the Tamiya F-4B and were used from 1958 to 1968..

This set includes four (4) empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Rocket tubes are hollow the entire length of the pod to dep..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Set includes four (4) Mk-82/BLU-111 bombs with the rough ablative coating, four (4) KMU-572 tail assemblies attached and the nose strake as separate pieces.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes four (4) Mk-82/BLU-111 bombs with KMU-572 tail assemblies attached and the nose strake as a separate piece.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes two (2) Thermally Protected Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

Set includes four (4) Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build F-4B's that were fitted with the AN/APR-25 antenna.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue in place an..

This part is designed to be used with Bullseye Model Aviation Decal Sheet 48-017 and Furball Aero-Design Decal Sheet 48-076 when building the VF-14 and VF-32 options.Mastered by Richard VanZandt, it is a drop in replacement for kit part P18/P19...

Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build early F-4B's, as well as USAF F-110 with little to no effort.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue i..

*** NOTE *** This sheet does NOT include the mask for the bat!Waterslide Decals printed by Microscale (Insert printed by Cartograf).5.5 x 8.5 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

This set provides correctly sized and detailed wing fold hinge covers for the Kinetic or Italeri (Kinetic plastic) EA-6B Prowler kits.A quick and light sanding of one edge to remove the support nibs is all that is needed. Simply pop into place and glue...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

This set includes four (4) BDU-57 / 59 / 60 Laser Guided Training Rounds with separate seeker heads.Careful removal of parts from print supports and minimal clean up required.Can be used with the F-14A/B/D, F/A-18A/B/C/D/E/F and AV-8B..

*Designed to be a drop in fit for the Hasegawa AV-8B series of kits. Simply paint and place in intake.* Some sanding may be required around the sides to get a proper fit.Master Patterns by Daniel Tompos..