Hypersonic Models

This is a cockpit set for Kitty Hawk's FJ-2 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place, a detailed rear cockpit bulkhead and turtle deck, the FJ-2 specific loop antenna assembly as well as a detailed canopy rear deck...

This is an airframe update set for Kitty Hawk's FJ-2 Fury. It includes a new intake nose ring with a corrected shape (the kit's nose is much too blunt) and cast-on one-piece air intake front part. There is detail scribing on the inside of the nose ring (absent on the kit parts). The nose wheel well ..

F-4 Phantom C/L pylon, 1:48, for the Zoukei Mura line of kits. The pylon fit on and into the detail moulded onto the ZM lower wing surface. It comes with two sets of separate pins - one for the larger stabiliser pins and the smaller sway brace pins that connect to the stores to be mounted...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

This is a full conversion set to build an NF-104A aerospace/astronaut trainer aircraft from the Kinetic F-104G kit. The set comes with all parts needed, some injection moulded plastic, some 3D printed, plus a turned brass pitot boom and a full set of decals by Caracal (printed by Cartograf)...

This is a conversion set for building an F-104B or early F-104D with downward firing C-1 ejection seats. As a base kit a Kinetic F-104D or TF-104G is needed. This conversion contains three new clear canopy parts (machine cast from transparent, UV stable resin), two C-1 seats plus ejection rails, a n..

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a corrected nose intake part for the Kitty Hawk FJ-3 Fury kit. It is a drop-in replacement for the kit part and features a corrected nose profile, in particular around the upper lip where the small radome is located. The kit part is too blunt, in the same way as the FJ-2 part is. The panel l..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is an update set for ClearProp's D-21 kit. It contains more detailed and more accurate engine sets (with one-piece nozzle), intake with one-piece spike, new back plate and better proportioned pitot and a camera to go behind the glass...

This is a set of 3D printed B-26K (A-26A) Counter Invader / Nimrod wheels. For the ICM kit in 1:48. The mounting points are designed for a direct fit to the kit axles. The wheel hubs are loaded with fine and accurate detail, from valve stems to visible springs in the brake pads. The tyres have very ..

Corrected tail surfaces (stabilisers, elevators and rudder) for the Kitty Hawk FJ-2 Fury (and early FJ-3). The FJ-2 kit only contains the ribbed elevators/rudder, which is correct for an FJ-3 and very late FJ-2's after transfer to the Reserves. FJ-2's in service (as well as early FJ-3's) had smooth-..

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/(D), but seen as late as 1973 on an F-4J. Separate, handed pylons are included. The tanks are cast in hollow halves that are very easy to clean up and assemble...

This is an upgrade set for Zoukei Mura Phantoms. As per the kit, the stabilators can only be mounted in one (or two) position(s). With this set, you can set the stabilators in any position of your choice and improve the detail on the stabilator pivot cover plates as well. Also included are the reinf..

F-4 Phantom outer pylons, Air Force type, 1:48, designed for the Zoukei Mura line of kits. The pylons have the correct outboard angle built in and come with separate sway brace pins so stores can be mounted at correct angles, either canted in line with the pylon or perpendicular to the ground...

Corrected A/C air intakes for Academy's F-4 Phantom series (F-4B, C and D so far). Drop fit resin replacement. All it takes is a little superglue and a swipe of filler to blend it in...

This is a centreline pylon for Kinetic's F-104 series, suitable for variants from C through to S. The item is 3D printed and packed with detailed features. The outer sway braces are fixed, while the two centre pads are separate pieces that can be adjusted to match the loadout being mounted. The pylo..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

This conversion set includes the AN/ANQ-126 fairings for the intakes (with mounting holes to match Tamiya's moulded-on pins), a fin cap with the correct sensor bulge for the N model, a new RIO instrument panel and an external rear view mirror. Further N specific parts are already included in the Tam..

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..