Maestro Models

..

How to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting mat)3. Grab the decal wit..

Used in many configurations on various prototypes and test beds for most Lansen versions. For Heller model kit...

History:The S29C Tunnan was converted J29B Tunnan fighters, fitted with five cameras that replaced the guns - so no armament was carried on this version - but it could be fitted with extra fuel tanks or ECM pods.The letter S was derived from Spaning, translating to reconnaissance in Swedish. A total..

..

History:Some Swedish Air Force Percival Pembrokes were fitted with radar equipment mounted in a SAAB 32 Lansen nose radome. At least two of them used the version supplied in this set. It was 83011 and 83012.Decals for 83011 (Adam 11) are available on RB studios decal sheet for Pembroke, including ma..

A set of Alps-printed 1/72 Forsokscentralen badges. Contains one sheet with 4 badges on itHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to ap..

How to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting mat)3. Grab the decal wit..

The short pylon (type J5) is used for the rocket pod and the longer rail is for Rb24. Remove parts from casting blocks. There are locator pins on adapters to fit in holes on the Y-pylon. Front end the of pylon is to be located 43 mm behind the nose wheel bay of Hasegawas kit...

The set contains engine cowling, propeller, exhausts and vacformed canopy resin parts...

This is a resin replacement vertical stabilizer tip for converting the Hasegawa 1/48 Draken kit to the early-model variants. To be used in conjunction with Maestro Models' early-version canopies and short air intake sets. Beautifully molded, and sure to be welcomed by Swedish Air Force fans...

..

..

This set converts the Tarangus 1/48 A32A Lansen to the recce model of this aircraft.It contains the external parts in resin plus a resin instrument panel with the typical hood for the back seat.For the more ambitious builder, there is also a very detailed interior set in colour photoetch (MMP4871)...

A set of Alps-printed decals with "FC" codes in three styles: 1935 model, 1964 model and modern. One sheet each of yellow and black letters. 1/72 scale. How to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer..

A set of Alps-printed decals with "FC" codes in three styles: 1935 model, 1964 model and modern. One sheet each of yellow and black letters.Solid decal film. NOTE! The yellow letters have a slight striped appearance on distances less than 12 inches. This is because the right yellow hue does not exis..

How to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting mat)3. Grab the decal wit..

How to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting mat)3. Grab the decal wit..