Model Planes

Some minor clean up of the forward end of the bomb will be required to remove the print support nibs. A few swipes with a file and sanding sticks does the trick.Set contains two Fire Bombs..

Mk-76 practice bombs (6 per pack)These new 3D printed bombs come ready to paint and install. Some very light clean up may be necessary at the aft end of the fins to remove any trace of the printing supports.Simply paint FS35109 Blue and install!..

While we have an extensive line of ordnance, we also understand that some modelers are perfectly content using the bombs provided in the kits. In some cases, the fuzes included with them leave a lot to be desired and may not be what you'd like to depict.This set provides 24 Mk-43 TDD (Target Dete..

While we have an extensive line of ordnance, we also understand that some modelers are perfectly content using the bombs provided in the kits. In some cases, the fuzes included with them leave a lot to be desired.This set provides 24 M904 nose fuses that will help enhance those kit supplied bombs..

3D ResinThis set includes four (4) bombs ready to paint and install on your model. Bombs come as shown in photo, with print supports removed. Light sanding of the aft edge of the fins required to remove print support nibs.CAD by Craig Sargent..

This set includes four (4) BDU-57 / 59 / 60 Laser Guided Training Rounds with separate seeker heads.Careful removal of parts from print supports and minimal clean up required.Can be used with the F-14A/B/D, F/A-18A/B/C/D/E/F and AV-8B..

Set of four (4) 3D printed launchersIn February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.Some slight modification ..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

This set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Pods are 3D printed and come ready to paint and attach to your m..

Designed by Petr Haupt, this set includes two (2) LAU-33 Pods, four (4) Mk-71 Rocket Motors, four (4) Mk32 Mod 0 anti tank / anti personnel warheads with Mk188 Impact Fuzes and four (4) Mk32 Mod 0 warheads with Mk93 proximity fuzes..

This set includes two (2) LAU-33 dual 5.00" Rocket Launchers with empty tubes.Used by the F-4 Phantom, F-8 Crusader, OV-10 Bronco..

3D ResinThis set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

These Missile Launchers are designed to fit the Trumpeter F/A-18E/F wing tip and should work with the Revell kit.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fits into slot on both kit wing tip parts.Fou..

These Missile Launchers are designed to fit the Trumpeter F/A-18E/F wing tip and should work with the Revell kit.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fits into slot on both kit wing tip parts.Fou..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) launchersUsed to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) missile launchers.Used to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchers.Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage..

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles...

LAU-115/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles. ..

3D ResinThis set includes two (2) LAU-10 rocket pods, eight (8) Mk-71 Mod 1 Rocket Motors, eight (8) Mk-32 Mod 0 AT/AP Warheads with Mk-93 Mod 0 Fuze and eight (8) Mk-32 Mod 0 AT/AP Warheads with Mk-188 Impact FuzesLAU-10 CAD by Matt FarrowRockets and warhead CAD by Dave Roof..

3D ResinThis set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.Designed by Matt Farrow of Shrunk Craft..