Model Planes

RS-82 Rockets (10 Pcs) (all kits)..

Refueling tube for CH-53E Super Stallion, MH-53E Sea dragon for Academy kit (3D printed)..

Rafale C cockpit (Detailed edition) for Revell/Academy kit (3D printed)..

Rafale C cockpit (Basic edition with 3D decals) for Revell/Academy kit (3D printed)..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

R.550 Magic-2 missiles (4 pcs) (Mirage F.1, Mirage 2000, Mirage III, Rafale, Super Etendard, MiG-21, Jaguar) (3D Printed)..

Set contains 3D-printed parts for detailing of propellers for the aircraft model PV-1 Ventura (Revell, Academy)...

Set contains 3D-printed parts for detailing of cowlings and engines for aircraft models PV-1 Ventura (Revell, Academy)...

1. Hawker Typhoon Mk. Ib , RB208/''K NL'', flown by Wg Cdr C.D. North Lewis, No. 124 Wing, B.86 Helmond, Netherlands, March 1945.2. Hawker Typhoon Mk. Ib , SW470/''JB'', flown by Grp Capt J.R. Baldwin, No. 123 Wing, B.103 Plantlunne , Germany, May 1945.3. Hawker Tempest Mk. V (Series 2), SN228/'..

1. Hawker Tempest Mk. V (Series 1), JN751/''R B'', flown by Wg Cdr R.P. Beaumont, No. 150 Wing, Newchurch , UK, June 1944.2. Hawker Typhoon Mk.Ib , MN570/''B'', flown by Wg Cdr R.E.P. Booker, No. 123 Wing, Thorney Island, UK, June 1944.3. Hawker Typhoon Mk. Ib , MN666/''C G'', flown by Wg Cdr C...

P-47C Thunderbolt 3D-Printed & coloured Interior on decal paper (Dora Wings)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or appl..

P-47 D-30 3D-Printed & coloured Interior on decal paper (Miniart)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or apply it to the..

P-40N interior 3D decals for Academy kit3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the dec..

P-39Q/N Airacobra 3D-Printed & coloured Interior on decal paper (Arma Hobby)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or appl..

F-100F-1-NA "Spirit of St.Louis II". Unit: 20th FBW, USAF. Serial: FW-730 (56-3730). Aircraft was named like this shortly after it was assigned to the 20 FBW, Wethersfield AB, Essex, England in 1957...

Naval Air Station Oceana - Acrylic 3 mm (410 x 270 mm) (410 g)..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

1. Ki-21-ll Ko (a) 62 Sentai 1 Chutai. Only the undersides of this aircraft were not painted in Green all other areas had an even application of paint. 62 Sentai became part of the 5th Hikoshidan in Tailand in January 1942.2. Ki-21-ll Ko (a) 3 Kokugun Based at Sembawang, Singapore following the en..

3D printno decal..

3D printno decal..

Set contains 3D-printed parts and coloured seat belts for detailing to build 2 seats for the helicopter models Mi-24...

Set contains parts for detailing of seat belts for the helicopter models Mi-24...

MiG-35 3D-Printed & coloured Interior on decal paper (HobbyBoss) (Small version)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or ..

MiG-35 3D-Printed & coloured Interior on decal paper (HobbyBoss)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or apply it to the ..