Model Planes

DZUS Fasteners (all kits)..

Set contains 3D-printed parts and coloured seat belts to build 2 seats for the aircraft model A-26 Invader...

Set contains 3D-printed parts for detailing of pylons for the aircraft models A-1 Skyraider (Tamiya)...

Do 335A-12 Trainer 3D-Printed & coloured Interior on decal paper (Tamiya)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or apply i..

DH98 Mosquito two stage merlin (Tamiya)resin set for Tamiya kit..

Set contains 3D-printed parts and coloured seat belts to build 2 seats 'F16F Rafale'...

Rafale C access ladder (3D Printed)..

D-704 Buddy air refueling store (early) (1 pcs) (A-4, A-6, A-7) (3D Printed)..

4 decal variants:1. C-4, 2nd Air Division Ceske Budejovice, Staff Capt. Posta, Plzen 1946 2. C-4.16, Cvichna letka 2, letiste Plana, Stkp. Perina, 1947 3. C.104.178, LSu Malacky, 1948 4. C.104.69, PS III, Olomouc, duben 1947** This model kit is supplied in unassembled and unpainted plastic compone..

CVS-18 USS WASP 1971 - Acrylic 3 mm (410 x 270 mm) (410 g)..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

Cowling fixtures and interior ribsPE accessories for scratch builders..

Chester Jeep race planeresin construction kit of golden years race plane..

CH-47F interior 3D decals for Italeri kit 3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the d..

CH-47D 3D-Printed & coloured Interior on decal paper (Italeri)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or apply it to the gl..

CH-47A 3D-Printed & coloured Interior on decal paper (Italeri)3D decals 1. Soak the decal in the warm water for a couple of seconds and after its separation from the backing paper position it on the model. 2. To increase the decal's adherence use the white glue, Mr. Mark Setter or apply it to the gl..

CH-46E interior 3D decals for Academy kit 3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the d..

CH-46E Cargo compartment interior 3D decals for Academy kit 3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Caudron CR 714 C-1 (RS Models kit)PE set for RS model kit..

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

C-130J engine nacells (Italeri kit)resin set for Italeri kit..

C-130 Wheelsresin set of wheels..

C-130 Sponsonsresin accessories for Hercules..

C-130 flaps (Italeri)resin set for Italeri kit..