Model Planes

This set includes four (4) highly detailed ADU-703 adapters with BRU-32 bomb racks for use on the Tamiya, Revell and Trumpeter 1/32 F-14A/B/D kits. Modification to the kit weapons rails will be necessary. Drawings with measurements on where to cut are provided.Released in cooperation with our frie..

Vinyl Mask..

3D ResinThis set includes twenty four (24) DSU-33 Proximity Fuzes. These are designed to work with all kit supplied bombs that may not have accurate or clean versions...

This set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene.Parts come as shown in photo. Very light sanding needed on one surface needed prior to painting...

3D ResinThis set includes one travel pod for use on all USN/USMC F-4 Phantom kitsCAD by Craig Sargent..

Designed for the GBU-31 with BLU-109 warhead included in the Academy F-16D and F-16I kits..

3D ResinThis set includes twelve (12) BDU-33 25lb practice bombs...

Set includes x 4 3D printed engines and cast resin adapters3D printed resin parts. Printing supports removed..

3D ResinThis set includes six (6) SATCOM Antenna with short mount found on a number of Helicopters. Use fine sprue cutters to remove part from support and lightly sand base smooth. Attach using super glue (CA)...

This set includes eight (8) wing pylons, one (1) centerline pylon, seven (7) BRU-36 ejector racks, and two (2) LAU-138 BOL launchers.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes eight (8) wing pylons, one (1) centerline pylons, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes six (6) wing pylons, two (2) centerline pylons*, seven (7) BRU-36 ejector racks and two (2) adapters used when the LAU-7 missile launcher is attached to the outboard pylons.*Different centerline pylons are configured for use with the strakes or gun pack.3D printed and designed..

Waterslide Decals printed by Microscale (Insert printed by Cartograf).8.5 x 11.0 inch sheet..

This set includes 9 pieces to Upgrayedd your Trumpeter AV-8B Day Attack Harrier kit...

This is a simple replacement for the slightly too thick kit supplied HUD's. Cut in clear .007 styrene, simply cut HUD from runner and apply to kit HUD frame, or any aftermarket photo-etch frame. Enough pieces for six aircraft are included...

Vinyl Mask..

Vinyl Detail..

This set contains two accurate fuel tanks for the AV-8B Harrier and Harrier GR.5/7/9Each tank comprises 5 parts with keys to correctly place both the fore and aft sections.Designed by Richard VanZandt of Flight Line Resin..

3D ResinThis set includes eight (8) AOA Probes. Can be used on the F/A-18A-D, AV-8B, A-6E, EA-6B and several others...

3D ResinThis set includes four (4) sets of antenna typically found on F/A-18A+/A++/C/D Hornets.Includes a vinyl template to aid in proper alignment...

3D ResinDesigned by Richard VanZandt, this set includes one (1) pod, comprised of three parts. Main body, alignment plug, and the tail section. Assembly required after minimal cleanup of parts...

This set contains one (1) pod. The AN/ALQ-164 Defensive Electronic Countermeasures (DECM) Pod was used exclusively and frequently by the US Marine Corps AV-8B Harriers during Operation Desert Storm.While limited in its use, the pod is still carried today by the US Marine Corps and is also used by ..

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

This set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts...