Print Scale 72-124 1/72 Henschel Hs 129 Decals

Type: Water-slide decals

1. Hs 129B-1./R2: 8./SchG 1: No. E (W.Nr. 0193), Eastern front, Russia, February 1943, time Is winter white coloring, located on top of the standard bi-color green camouflage; on-board code just partially colored in white paint.

2. Hs 129B-1. part: 8./SchG 1: (G) the Kursk bulge, summer 1943, 8./SchG 1 was formed in Lippstadt, actively participated in the battle of Kursk in the summer of 1943 and in October 1943.

3. Hs 129B -2/R-2 Part 10 . (Pz)/SG 9 "K" Ukraine, in Marck 1944.

4. Hs 129B-2/R2 Part 8 (Pz) /SG 1 "J", W.Nr. 0364, Kuban, the end of summer 1943.

5. Hs 129B-2/R2 Part 8 (Pz) /SG 1 "J", W.Nr. 0364, Kuban, the end of summer 1943.

6. Hs 129B-2 , Stab/SchG 1 "<-" W. Nr. 0288, Stalingrad, the winter of 1942-43.

7. Hs 129B-2/R2, 4 (Pz)/Sch G 1 "F" Russia. October 1942.

8. Hs 129B-1 , 5./SchG 1. Eastem Front, Summer 1942.

9. Hs 129B-2, 8 (Pz) /SchG2 "X", W.Nr 0278 EL Auina, Tunisia, early 1943.

10. Hs 129B-3/Wa, 14 (Pz)/ SchG 9, "<-" (ex NN+KF) Eastem Front, Winter of 1944-1945.

11. Henschel Hs 129B-2 (code: +TQ, W/Nr.141537) by Oberleutnant Bartel of the 13 (Pz)/SG 9. destroyed by own personnel.
Wagrowitz (Torndorf) airfield Poznan region 22 January 1945.

13. Hs 129B-2/R2, 4 (Pz)/Sch G 1 "F" Russia. October 1942.

14. Hs 129B-2 "Haifetito" Escadrila 60 asalt, Grupul 8 Asalt "327" Pilot -Lazar Muntinyu.

How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.