Print Scale 72-131 1/72 Cessna O-1 Bird Dog Decals
Out Of Stock
Type: Water-slide decals
1. L-19A of the 8th Army was used to transport President elect Dwight D. Eisenhower on an inspection trip of Korea in December of 1952.
2. TO-1D carries the high visibility Gloss White end Red scheme used for aircraft that operated over the Arctic or jungle areas.
3. Cessna O-1D " Little Annie Fanny", 199th Reconnaissance Airplane Company, the " Swamp Foxes" Vinh Long, RVN, understand was flown bu Rich Burns. Mid-60s.
4. This shark mouthed O-1D of the 19th TASS was one of the first Air Force Bird Dogs to deploy to Vietnam during July of 1963.
5. Marine Corps OE-2 (O-1C) of VMO-6 based at Chu Lai, South Vietnam during the early 1960s.
6. A number of Air Force O-1s carried three color camouflage schemes that varied from aircraft to aircraft. The Orang identification panels on the wing uppersurface helped attack aircraft spot the O-1.
7. Cessna O-1C, US Marines Corps, BuAer 140100, System Test Division, NAS Patuxent River MD, ca.1965.
8. Cessna O-1D Bird Dog, Cambodian Air Force, s/n 23529 (55-4689),Pochentong Air Base, ca 1972.
9. Cessna O-1E Bird Dog of the 112th Liaison Squadron, 23rd Tactical Wing, Bien Hoa during 1966.
10. MAJ Boung used this VNAF O-1A to South Vietnam with his wife and five children. MAJ Boung made the first landing bu an O-1 on an aircraft carrier, landing on USS MIDWAY on 30 April 1975.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. L-19A of the 8th Army was used to transport President elect Dwight D. Eisenhower on an inspection trip of Korea in December of 1952.
2. TO-1D carries the high visibility Gloss White end Red scheme used for aircraft that operated over the Arctic or jungle areas.
3. Cessna O-1D " Little Annie Fanny", 199th Reconnaissance Airplane Company, the " Swamp Foxes" Vinh Long, RVN, understand was flown bu Rich Burns. Mid-60s.
4. This shark mouthed O-1D of the 19th TASS was one of the first Air Force Bird Dogs to deploy to Vietnam during July of 1963.
5. Marine Corps OE-2 (O-1C) of VMO-6 based at Chu Lai, South Vietnam during the early 1960s.
6. A number of Air Force O-1s carried three color camouflage schemes that varied from aircraft to aircraft. The Orang identification panels on the wing uppersurface helped attack aircraft spot the O-1.
7. Cessna O-1C, US Marines Corps, BuAer 140100, System Test Division, NAS Patuxent River MD, ca.1965.
8. Cessna O-1D Bird Dog, Cambodian Air Force, s/n 23529 (55-4689),Pochentong Air Base, ca 1972.
9. Cessna O-1E Bird Dog of the 112th Liaison Squadron, 23rd Tactical Wing, Bien Hoa during 1966.
10. MAJ Boung used this VNAF O-1A to South Vietnam with his wife and five children. MAJ Boung made the first landing bu an O-1 on an aircraft carrier, landing on USS MIDWAY on 30 April 1975.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: Out Of Stock
- Reward Points: 20
- SKU: PRS72-131
Print Scale
MRP: US$16.84 Save: US$3.03
18% OFF
US$13.81
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.