Print Scale 72-141 1/72 Wet Decals - Fairey Battle (1 sheet)
Out Of Stock
Type: water-slide decals
1. Battle MK. I part: 12 Sqn, RAF No.: V (P6597) Binbruk, United Kingdom, July, 1940.
2. Fairey Battle Target Tug. No.92, Irish Army Air Corps, 1941. Dark Green/Dark Grey Night finish with two - colour national marking over a white background on the fuselage and tri-colour(orange outboard) 20 inch-wide band around wings. Scrap view shows a different scheme with a Donald Duck cartoon on the fuselage side: Get Quacking.
3. Battle Of: the RAAF No. 89 (L5789) this aircraft was operated in the school shooters RAAF, as towing targets in 1943.
4. Turkey Fairey Battle Mklll, 2829/29, Turkish Air Force. Dark Green/Dark Earth/ Night finish; red rudder with white crescent and star superimposed. Red/white wing markings; serial 2929 in white under wings, and 29 in black on fuselage sides.
5. Fairey Batle Mk l K9299/GV, No.103 Squadron (RAF), Benson, early 1939. Dark Green/ Dark Earth/ Night finish with white codes; black serial on fuselage and rudder, white under wings reading from leading edge under port and from trailing edge under starboard A type roundels on fuselage and above wings; note unit badge on fin.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. Battle MK. I part: 12 Sqn, RAF No.: V (P6597) Binbruk, United Kingdom, July, 1940.
2. Fairey Battle Target Tug. No.92, Irish Army Air Corps, 1941. Dark Green/Dark Grey Night finish with two - colour national marking over a white background on the fuselage and tri-colour(orange outboard) 20 inch-wide band around wings. Scrap view shows a different scheme with a Donald Duck cartoon on the fuselage side: Get Quacking.
3. Battle Of: the RAAF No. 89 (L5789) this aircraft was operated in the school shooters RAAF, as towing targets in 1943.
4. Turkey Fairey Battle Mklll, 2829/29, Turkish Air Force. Dark Green/Dark Earth/ Night finish; red rudder with white crescent and star superimposed. Red/white wing markings; serial 2929 in white under wings, and 29 in black on fuselage sides.
5. Fairey Batle Mk l K9299/GV, No.103 Squadron (RAF), Benson, early 1939. Dark Green/ Dark Earth/ Night finish with white codes; black serial on fuselage and rudder, white under wings reading from leading edge under port and from trailing edge under starboard A type roundels on fuselage and above wings; note unit badge on fin.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: Out Of Stock
- Reward Points: 22
- SKU: PRS72-141
Print Scale
MRP: US$18.68 Save: US$3.24
17% OFF
US$15.43
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.