Print Scale 72-518 Decal for 1/72 Wing Commander Typhoons and Tempests of the 2nd TAF

1. Hawker Tempest Mk. V (Series 1), JN751/"R B", flown by Wg Cdr R.P. Beaumont, No. 150 Wing, Newchurch , UK, June 1944.

2. Hawker Typhoon Mk.Ib , MN570/"B", flown by Wg Cdr R.E.P. Booker, No. 123 Wing, Thorney Island, UK, June 1944.

3. Hawker Typhoon Mk. Ib , MN666/"C G", flown by Wg Cdr C.L. Green, No. 121 Wing, Holmsley South, UK, June 1944.

4. Hawker Typhoon Mk.Ib , MN941/"DJS", flown by Grp Capt D. J. Scott, No. 123 Wing, B.53 Merville, France, Sept. 1944.

5. Hawker Typhoon MK IB MN855/WPB, flown by Wing Commander William Pitt-Brown, 121 Wing, B.5 Le Fresne-Camilly,August 1944.

6. Hawker Typhoon Mk. Ib , MN587/"ZZ II", flown by Grp Capt D.E. Gillam, No. 146 Wing, B.70, Deurne, Belgium October 1944.

7. Hawker Tempest Mk. V (Series 2), EJ706/"RPB", flown by flown by Wg Cdr R.P. Beaumont, No. 150 Wing, B.80,Volkel, Netherlands, October 1944.

8. Hawker Tempest Mk. V (Series 2), EJ750/"JBW", flown by Wg Cdr J.B Wray, No. 122 Wing, B.80, Volkel , Netherlands, November 1944.

9. Hawker Typhoon Ib RB205/"FGG", flown by Wg Cdr F.G. Grant, No. 143 Wing, Eindhoven, Netherlands, October to December 1944.

10. Hawker Typhoon Mk. Ib , RB208/"K NL", flown by Wg Cdr C.D. North Lewis, No. 124 Wing, B.86 Helmond, Netherlands, March 1945.

11. Hawker Typhoon Mk. Ib , SW470/"JB", flown by Grp Capt J.R. Baldwin, No. 123 Wing, B.103 Plantlunne , Germany, May 1945.

12. Hawker Tempest Mk. V (Series 2), SN228/"EDM", flown by flown by Wg Cdr E.D. Mackie (RNZAF), No. 122 Wing, B.152, Fassberg , Germany, April May 1945.

Water-slide Decals:

Instruction:
1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2.Cut out the decal you need (do it on cutting mat)
3.Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4.Remove the decal from the water and place it on paper towel to remove any excess water.
5.Apply decal solution to the part where the decal is to be placed.
6.Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7.Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Clear/Future to seal it.