Print Scale 72-460 Decals for 1/72 Messerschmitt Bf 109. Spanish War
"1. Bf 109B2 2.J88 Condor Legion 6x60 Herbert Schob La Cenia Spain late 1938. RLM 77, RLM 65.
2. Bf 109D-1 of 3/J 88, Spain, November 1938 Pilot, Hauptmann (Captain) Werner Molder. RLM 62, RLM 65.
3. Bf 109D-1 2.J/88, Legion Condor - Gotthard Handrick (5 victories). 18 June 1937 - 10 September 1938. RLM 62, RLM 65.
4. Bf109D-1 ""Legion Condor"" Fighter Group Commander 88 Pilot: Hauptmann Walter Grabmann (final score 7), late 1938, Spain. RLM 62, RLM 65.
5. Me 109D 1/J 88, Spain, August 1938. Pilot, Oblt. (Lieutenant) Otto Bertram. This aircraft was shot down on October 4, 1938.
6. Bf 109V-3 Obit. Hannes Traufloft, J/88, Sivilla/ Tablada airfield, December 1936. One of the first Bf 109s to go to Spain was the Bf 109V-3 flown by Trautloft. Finish was factory standard light grey with Spanish markings applied and This eventually became the emblem of JG 54. The spinner is brown and white with a green tip.
7. Bf 109D 1/J 88, Spain, June 1938.Pilot Lieutenant Wolfgang Schellmann. RLM 62, RLM 65.
8. Bf 109 B-1 2/J 88, Spain, spring 1937. Pilot, Unteroffizier Norbert Flegel.
9. Bf 109B-1 of 2/J 88, Spain 1937.This device was captured by the Republicans and tested by the French to join the Russia.
10. Bf 109B-2 of 2/J 88, Spain, July 1937.Pilot, Unteroffizer (Sergeant) Wilhelm Staege." Water-slide Decals: Instruction:
1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2.Cut out the decal you need (do it on cutting mat)
3.Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4.Remove the decal from the water and place it on paper towel to remove any excess water.
5.Apply decal solution to the part where the decal is to be placed.
6.Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7.Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8.When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
2. Bf 109D-1 of 3/J 88, Spain, November 1938 Pilot, Hauptmann (Captain) Werner Molder. RLM 62, RLM 65.
3. Bf 109D-1 2.J/88, Legion Condor - Gotthard Handrick (5 victories). 18 June 1937 - 10 September 1938. RLM 62, RLM 65.
4. Bf109D-1 ""Legion Condor"" Fighter Group Commander 88 Pilot: Hauptmann Walter Grabmann (final score 7), late 1938, Spain. RLM 62, RLM 65.
5. Me 109D 1/J 88, Spain, August 1938. Pilot, Oblt. (Lieutenant) Otto Bertram. This aircraft was shot down on October 4, 1938.
6. Bf 109V-3 Obit. Hannes Traufloft, J/88, Sivilla/ Tablada airfield, December 1936. One of the first Bf 109s to go to Spain was the Bf 109V-3 flown by Trautloft. Finish was factory standard light grey with Spanish markings applied and This eventually became the emblem of JG 54. The spinner is brown and white with a green tip.
7. Bf 109D 1/J 88, Spain, June 1938.Pilot Lieutenant Wolfgang Schellmann. RLM 62, RLM 65.
8. Bf 109 B-1 2/J 88, Spain, spring 1937. Pilot, Unteroffizier Norbert Flegel.
9. Bf 109B-1 of 2/J 88, Spain 1937.This device was captured by the Republicans and tested by the French to join the Russia.
10. Bf 109B-2 of 2/J 88, Spain, July 1937.Pilot, Unteroffizer (Sergeant) Wilhelm Staege." Water-slide Decals: Instruction:
1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2.Cut out the decal you need (do it on cutting mat)
3.Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4.Remove the decal from the water and place it on paper towel to remove any excess water.
5.Apply decal solution to the part where the decal is to be placed.
6.Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7.Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8.When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
General Info | |
Scale | 1/72 |
Type | Model Upgrade/Accessory |
Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 20
- SKU: PRS72-460
- 1pcs in Stock
Print Scale
MRP: US$16.84 Save: US$3.03
18% OFF
US$13.81
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.