Echelon Fine Details D356063 Decals for 1/35 720th Military Police Battalion V100s in Vietnam (Pt3)
Water-slide Decals
Two versions of the yellow/green shields covered, with "THE VULTURE" using the lesser seen or more unique variety. Both are hard to tell apart unless you pay attention to the details (pistol size, black vehicles, letters, and shape of shield). And if you think the "MILITARY POLICE" marking on the sides were the same across every vehicle (even those parked right next to each other) - think again! There were differences in font type, size and spacing as well. It is interesting to know that both vehicles were a pair and each are uniquely marked!
As the black markings were thin-outlined with white, they have been separated from the yellow/green shields as it is nearly impossible to get every print perfectly registered without sacrificing many.
The artworks on both vehicles' front (and different shields) are painstakingly captured down to the last detail.
This set also comes with patches and insignias for the MP's brassards.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
Two versions of the yellow/green shields covered, with "THE VULTURE" using the lesser seen or more unique variety. Both are hard to tell apart unless you pay attention to the details (pistol size, black vehicles, letters, and shape of shield). And if you think the "MILITARY POLICE" marking on the sides were the same across every vehicle (even those parked right next to each other) - think again! There were differences in font type, size and spacing as well. It is interesting to know that both vehicles were a pair and each are uniquely marked!
As the black markings were thin-outlined with white, they have been separated from the yellow/green shields as it is nearly impossible to get every print perfectly registered without sacrificing many.
The artworks on both vehicles' front (and different shields) are painstakingly captured down to the last detail.
This set also comes with patches and insignias for the MP's brassards.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/35 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 12
- SKU: EC D356063
- 1pcs in Stock
Echelon Fine Details
MRP: US$10.36 Save: US$2.20
21% OFF
US$8.16
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.